最新動态：

• 無錫歐駿入駐品牌強國

• 綜合支吊架如何采購 有些事情需要了解

• 裝配式支吊架在施工過程中優勢有哪些？被廣泛使用嗎？

• 抗震支架在安裝中需要注意哪些問題

• 固定抗震支架需要考慮的點有很多

• 綜合支吊架/消防管道抗震支架進場一般要做哪些檢驗？

• 抗震支架在鋼結構工業廠房的應用

• 抗震支架規範詳情介紹

• 電纜橋架的荷載的介紹

• 電纜橋架基礎知識安裝發展的分析

電纜橋架基礎知識安裝發展的分析

抗震支架裝置進程中有哪些留意事項、

What precautions should be taken in the process of anti-seismic bracket installation?

1、留意裝置進程中應預留一定的地位

1. Pay attention to reserving a certain position in the process of installation.

由于溫差的變化會招緻抗震支架的管道資料的冷膨脹反響，因而會抗震支架發生一定的位移，因而在裝置時應預留一定的地位。而在特殊管道中設置抗震支架時應能掌握間隔，抗震支架制造商特别強調在拐角處必需設置一個架子，彼此之間的間隔比間隔之間的設計要求應該添加一個抗震支架。

Because the change of temperature difference will cause the cold expansion response of pipeline data of seismic bracket, the displacement of seismic bracket will occur, so a certain position should be reserved in the installation. When installing anti-seismic brackets in special pipelines, the spacing should be mastered. The manufacturers of anti-seismic brackets emphasize that a bracket must be installed at the corner. The design requirements of the spacing ratio between the brackets should be added.

2、留意裝置進程中的比例設計必需有嚴厲的計算

2. Pay attention to rigorous calculation of proportion design in the process of installation

抗震支架廠家在裝置時強調，特别是風管承荷載系數需求運用有關規則的公式依照實踐狀況計算，由于一切裝置設計必需十分迷信嚴謹，不能有任何武斷。同時還有水管和金屬管相關系數的選擇和計算，抗震支架模型和設計必需停止檢驗和校核，必需确認滿足要求才幹運用。

When installing the anti-seismic bracket, the manufacturer emphasizes that, in particular, the load-bearing coefficient of air duct should be calculated according to the formula of relevant rules according to the actual situation, because all the device design must be superstitious and rigorous, and there can be no arbitrary. At the same time, the selection and calculation of the correlation coefficients of water and metal pipes are also included. The model and design of the anti-seismic bracket must stop checking and checking, and it is necessary to confirm that the application can meet the requirements.